A Nice Lesson: How To Change Guitar Strings?

September 16, 2022 by No Comments

Many people enjoy playing the guitar. However, some people lack the knowledge of how to change a guitar string; this article will explain it in detail.

Whether you’re a novice or a guitar virtuoso, knowing how to restring your instrument can be a useful skill. Even though an electric guitar will require restringing more frequently than an acoustic guitar, this is still necessary to ensure proper sound quality. Keep your strings maintained and in tune before jamming out or singing the love song that you wrote.

How To Change Guitar Strings?

1. Gather The Tools

2. Loosen The Old Strings

You may have heard that it is best to not cut all the strings at once. According to the theory, removing all of the strings will cause your guitar neck to become unbalanced because there will be nothing to balance the tension from the truss rod.

When you want to remove a string, pull it until it reaches the tuning peg on the guitar’s headstock. Tuning instruments are typically wound clockwise to loosen them. As you unwind the string, you should hear a pitch decrease.

As you unwind the string, pay attention to what it is saying. You wouldn’t be able to tell if you were winding up or down without this feedback. And it will break if you wind it up!

Once enough tension has been released, either simply cut the string or keep unwinding it until it can be completely removed. The string should now be taken off the tuning device and the instrument’s bridge.

Once the string is sufficiently loose, you should be able to pull in a circular motion to remove it from the tuning machine. A set of pliers will enable you to complete the task if it becomes stuck.

3. Remove The String Ends

Pull up the bridge pins to release the string from this end once they are loosened.

On steel-string acoustic guitars, the string wire is normally attached to a ball-end which is secured in the bridge by one of six small pins. To get the string out, the pin must be taken out. Highly recommended is the Snapz Bridge Pin Puller[?], which does a fine job at pulling these out.

Some acoustics use a pinless system. If so, all you have to do is push in the direction the ball end is facing.

A string can get caught in the hole occasionally. If this occurs, you can cut a small piece from one of the large strings and use it as a ream to push the stuck string out from the other side.

4. Clean The Fretboard

This is your chance to clean the fretboard.

You ought to have taken all of the outdated strings off the bridge by this point. You should be staring at an empty fretboard.

You can either proceed directly to attaching the new strings or you can clean and oil it first.

Use some Steel Wool, 0000 Grade to gently scrub off any dirt and grime from the fretboard, especially around the frets. If you’d like, you could also use it to polish the frets to a mirror-like shine.

Now dust off the fragments of steel wool with Planet Waves UNTREATED Cloth and spray the Dunlop 65 Cleaner onto the fretboard, gently scrubbing and polishing until it’s clean.

5. Oil The Fretboard

Apply some lemon oil to the fretboard for a polished appearance. Make sure to use a cloth to remove any leftovers.

For one last professional touch, dab some Dunlop Lemon Oil all along the fretboard. Avoid being too liberal because the cleanup is messy. Rub it into the fretboard until it is completely gone, leaving a fresh, oiled surface. fretboard for you to play with.

6. Insert A New String

7. Wind The New String

Put the string in the tuning device, then get ready to wind.

Pull the loose end of the string toward the guitar neck after it has been fastened to the bridge. Put it in the slot that was previously occupied by the old string and feed it through the nut. A hole should be facing the nut when the tuning machine is wound. Through that hole, insert the string.

Give yourself plenty of slack in the section of the string between the bridge and the nut since you want to wind the string around the tuning machine for two to three full revolutions. One way to do this is to place your entire right arm or wrist underneath the string and then, using the index finger of your picking hand, gently hold the string to prevent it from slipping out of the nut.

The First Revolution

Guide the loose end under the end you are holding for the initial revolution.

Wind the string counterclockwise, holding it in place. While winding the tuning machine, take care that the end of the string you are holding doesn’t move.

For the first revolution, you ideally want to make sure the end you are holding passes over the loose end that is jutting out the other side of the machine head. however, only for the initial revolution!

The Other Revolutions

Allow the loose end to wrap above the end you are holding for the remaining revolutions.

You’ll need to take your hand out from under the string as it becomes tighter. Continue to be cautious to prevent the string from flapping and unwinding on its own.

For all remaining revolutions, you want to make sure that the end you are holding passes underneath the loose end of the string. The result of this is that the portion of the string that is wound around the tuning peg will end up on top of the part of the string you are holding, which means that as the string gets tightened, it will rest on the nut and break off at a downward angle, creating a more secure and reliable string installation.

Guitar Strings
Guitar Strings

8. Clip Off The Loose End

Cut the loose ends as precisely as you can.

Cut off the frayed ends with a pair of wire cutters. Even a pair of nail clippers will do in a pinch, even though that isn’t what they were designed for.

There shouldn’t be any extra loose string sticking out if the strings have been correctly installed. You can cut that string very, very close, and it is not moving.

9. Tune It Up

Tune each string to pitch using a guitar tuner. Repeat several times because each string will tighten the neck and affect how the other strings to tune.

The strings will be prone to going out of tune during the first hour or so of playing. You can either just start playing and tune as necessary, or you can gently pull on each string before tuning.

FAQ:

How Do You Get The Strings Out Of The Bridge?

Using bridge pins, each string is fixed in place. For removing these, a string winder has a small slot. You can also gently push them up by inserting your hand inside the sound hole. I’ve tried pulling them out with my fingertips as well, but it can be challenging because they are firmly wedged in.

Are The Old Strings Appropriately Cut?

Always don’t. If you have an extra set, you can untangle the strings before cutting them. This method is easier because it makes taking the string off the peg much simpler.

Tuning The Guitar Up

Make sure your strings are tuned to the right pitch by using a guitar tuner app. Gently pull each string to give it a little stretch after you’ve tuned the guitar. You’ll need to tune it once more after you’ve done this. Until it remains in tune, repeat this step a couple of times.

Trimming The Strings

In case one of my wraps doesn’t hold, I save this step for last. I once experienced a second string that wouldn’t hold because I hadn’t left enough slack, and because I had already trimmed it, it was very difficult to get it to grip the peg.

Use the wire cutters to cut the extra string as close to the peg as you can before trimming the strings. Observe carefully to prevent accidentally cutting the string that is under tension rather than the extra section.

I hope that after reading this article, everyone will be better able to learn more knowledge about guitar, and I wish everyone’s guitar level will become more and more advanced.